These tools are described as, made of steel hardened and tempered at the tip used to loosen or tighten screws.

Name a screwdriver with a wedge shaped and resembles a negative sign.

A kind of screwdriver that has a cross tip resembling a positive sign. This is used to drive screw with cross slot head.

This comes in either Standard or Phillips screwdriver with short shank or blade and a shorted handle.

This could be in the shape of screwdriver or a wrench. Its function is to drive screws with hexagonal slot heads.

These are tools used for pounding and driving or pulling out nails.

These are tools made from metal with insulators in the handle and are used for cutting, twisting, bending, gripping wires and cables.

A tool used for gripping, holding, and cutting electrical wires and cables and even small nails.

This type of Pliers is used for cutting fine, medium, and big wires and cables.

This is used for cutting and holding fine wires. This can reach tight spaces or small openings.

This special tool is used for removing insulation of medium sized wires ranging from gauge #10-#16,

This is used by linemen to remove the insulation of wire and cables in low and high voltage transmission lines.

A small drilling machine with a chuck capacity of ¼ to 3/8. It is used in making holes on metal sheets and concrete walls.

This tool is used to cut metal conduit and armored cable.

A device that acts as a convenient source of electrical energy for current consuming appliances.

This device is inserted to a convenience outlet to conduct electric current.

A circuit protective device that automatically blows and cuts the current when an overload or short circuit occurs.

Give an electrical device which function is to connect and disconnect the flow of electric current in a circuit.

A protective device used to automatically cuts the current when trouble in the circuit such as short circuit or overload occurs.

It is an octagonal shaped electrical material where the connections or joints of wire are being done.

A rectangular shaped metallic or Plastic (PVC) material in which flush type of convenience outlet and switch are attached.

Name an electrical device used for temporary wiring installation and commonly used for extension cord assembly.

An electrical conductor that is made of multiple strands joined together to make a single wire.

It is made of single strand of copper or aluminum wire. These are used in wiring installation inside and outside the buildings.

Electrical materials used to hold and anchor electrical conduits to their proper position.

What is the purpose of turning the drill on before attempting to drill a hole.

The purpose of moving the drill and the bit up and down often while drilling deep holes is to

What will likely happen if a large capacity portable drill bit jams during the drilling operation?

What kind of pressure should be applied to a drill during the drilling operation?

What type of drill is needed for wood drilling operation?

What type of drill speed is needed for most metal drilling operations?

What is the purpose of a pilot hole when drilling?

What should the operator do to prevent seizing when drilling?

What personal protective equipment should be worn when operating the portable disc grinder?

When operating the portable disc grinder, the grinding disk should be positioned so that the sparks and grit are thrown _____.

Grinding with the portable disc grinder should not be done in an area which______________.

The grinding disc should be replaced when worn out and reduced to _____________ of its original diameter.

Hands and arms should be protected by wearing ____________ when using the portable disc grinder.

What may possibly happen when the wire brush attachment is used on the portable disc grinder?

When the portable disc grinder is laid down, it should be positioned _____________.

The part shown in the illustration is the ________________.

The external part of the drill shown in the illustration is the ________________.

It is a hand-held rotating machine used for grinding and cutting processes depending on the type of disc fitted to the machine

It is a small drilling machine with a chuck of ¼” and 3/8”. It is used to bore holes on lighter metal work.

The part shown in the illustration is the ________________.

In the illustration, what is the reading in ohmmeter scale if the range is at X1.

What is the voltage if the scale is at 10 volts range?

What is the voltage if the scale is at 50 volts range?

What is the voltage if the scale is at 250 volts range?