This is used for griping, holding, cutting electrical wires and cables and even small nails. Usually used by linemen in doing heavy tasks.

Used for cutting and holding fine wires. This can reach tight space or small opening where other pliers cannot reach and used in making terminal loops of copper wires.

This has a cross tip resembling a positive (+)sign. It is used to drive screws with cross slot heads.

This tool is used in driving, pounding, and pulling out nails.

A tool used for removing insulation of medium sized wires ranging from gauge #10 to gauge #16 

A small drilling machine with a chuck capacity of ¼” to 3/8”. It is used in making holes on metal sheets and concrete walls.

It comes in either standard or Philips screwdriver with short shank or blade and shorted handle used to turn screws in tight space where standard screwdriver cannot be used.

It is used by linemen to remove insulation of wire and cables in low and high voltage transmission lines.

It is a device inserted to a convenience outlet to conduct electric current. A flat cord is attached to it on one end and the other end is connected to a current consuming instrument or appliance.

This is a circuit protective device that automatically blows and cut the current when an overload or short circuit happens.

This is a rectangular shaped metallic or plastic(PVC) material in which flush type of convenience outlet and switched are attached.

They are electrical materials used as the passage of wires for protection and insulation.

It is a form used to request for tools and equipment needed for a particular job.

The raw materials, work-in-process goods and finished goods that are the portion of a business's assets those are ready or will be ready for sale.

It is a written instruction to perform a work according to specified requirements, within specified timeframe and cost estimates.

An instrument used to measure the amount of electrical current intensity in a

circuit.

A pocket sized tool used to test the line wire or circuit if there is current in it.

A measuring tool used to measure the length of an object in centimeter and inches.

It is used to measure the diameter of wires/conductors in circular mils. It can

measuresmall and big sizes of wires and cables.

It is used to measure the voltage, resistance and current of a circuit. It connected in parallel or series with the circuit depending on what to measure.

An action to clean your workplace thoroughly so that there is no dust on floor, machines, and equipment?

A condition of training people to follow cleaning disciplines independently.

An action to identify and eliminate all unnecessary items from your workplace and dispose them.

An action to arrange or put every necessary item in good order so that they can be easily picked for use. A place for everything, everything is in place

A condition of always maintaining high standard of cleaning and workshop organization.

To remove the insulator of the TW #18 AWG solid cu. wire, what is the best tool to use?

This is a metal box where all circuit breaker place.

An electrical material used as the passage of wires for protection and insulation?

It is used to attach metallic or non-metallic conduit to the junction or utility boxes.

It is an octagonal shaped electrical material where the connections or joints of wires are being done? It is also where the flush type of lamp holder is attached.

This is used as a temporary tap usually done in constructions sites. The easy twist will facilitate tap wire movement.

This is the most widely used splice or joint in exterior wiring installation to extend the length of wire from one point to another.

The same application is done as in plain tap and the only difference is that this tap is a combination of two plain taps place side by side with each other.

If you want to prolong the wire inside a conduit. What splices you are going to use?

This is a two-tap wire turned simultaneously and is used where the two-tap wire is under heavy tensile stress.

This type of pliers is used for cutting fine, medium and big wires and cables.

A device that acts as a convenient source of electrical energy for current consuming appliances.

A device that connects and disconnects the flow of electric current in a circuit.

A protective device used to automatically cut the current when trouble in the circuit such as short circuit or overload occurs.

 It is made of a single strand of copper or aluminum wire.

It is made of multiple strands joined together to make a single wire.

It is used in determining the size of wires/conductors

It is also called tong-tester. It is used to measure current flowing in a conductor.

A device that connects and disconnects the flow of electric current in a circuit.

This tool is used to cut metal conduit and armored cable.

A devices that hold and protect the lamp.

Isa duplex stranded wire used for temporary wiring installation and commonly used in extension cord assembly.

These screwdrivers are designed for removing and inserting screws in place where it is impossible to use a straight shank screwdriver.

A small hand tool having a spiraled shank, a screw tip, and a cross handle and used for boring holes.

Uses a hand operated crank handle to turn an interlocking gear, which in turn rotates the drill bit.