A rectilinear figure bounded by more than five sides :

A line 135 m long represents 22.5 cm on plan, then R.F is :

As per Indian standard, the length of one link in 30 inter chain is:

The total number of zeros graduated on surveyor's compass is:

If the whole circle bearing of a line is 260°, its reduced bearing is :

In plane table survey measuring of lines and angles is mostly dispensed, but they are obtained :

The alidade used in plane table survey, its bevelled edges is also known as:

Scale of chord is used to measure :

A King post truss consists of two longer inclined member known as:

Survey conducted for unearthing relics of antiquity :

The maximum value of measurement in quadrilateral bearing is:

Lines passing through points having same declination at a given point is:

……………is done to set the plane table in meridian at successive station.

To locate an electric pole near the plane table station :

The method used for locating station points only by sighting towards well defined objects :

Leveling is the art of finding the…….. of the objects on the surface of the earth.

Reduced level is also known as:

The error is leveling operation during settlement of tripod on turning point is:

The staff reading on a certain peg is 1.680 when the staff is held 0.25 m out of the plumb in its total length of 4 m. The correct reading for the staff held vertical is:

In rise and fall method of reduction of levels provides a check on :

Crop period is the time elapsed between :

For a closed traverse the algebraic sum of the deflection angle is equal to :

The constant vertical distance between two consecutive contours is called :

In Theodolite traversing method consists in measuring the several angles successively and finally closing the horizon at the starting point :

The vertical circle of the instrument is on the left of the observer while taking a reading, the position is called :

The functional 1 key for ortho command used in CAD:

The CAD command used to lengthen or shorten the lines or object is :

The drafting setting used to pick a geometric point on an object is:

The CAD command used to join 2 parallel line is :

In a well conditioned triangle, no angle should be less than :

Number of arrows accompanying each chain :

In one setting up of the level the maximum number of back sight and fore sight is:

In Leveling station is a point where :

Contour map is used for :

Plunging or reversing of the theodolite telescope is also called :

The type of bond employed in brick work consist of alternate courses of headers and stretchers :

Agate cap is fitted with a :

The closing error in a closed traverse is adjusted by:

For ranging a line number of ranging rod required is:

Curvature effect of the earth is taken into account in :

The T- square is used for drawing:

To prevent warping of the board ……… are cleared at its back.

The first dimension line should be placed atleast :

The sum of the included angle of a hexagon is:

The angle of inclined letters :

The standard size of By imperial drawing is :

The lowest part of the structure which transmit the load to the soil is :

A right angled parallelogram with its opposite sides are equal :

Number of bricks required for one cubic meter :

A lintel is provided :

The Diameter of the graduated circle on the lower plate determines the :

In Theodolite the verniers A and B are marked in:

Pantagraph is used for :

Simplify : 44 – [33 – {44(33 – 44 – 33)}]

Factorize : 49x2 - 81y2=

The equation of a straight line in a graph is shown by :

The value of sine 90° is:

The value of 1 + tan2θ is :

One chain is :

The base unit of length in S.I system :

The multiple factor of the prefix deci is :

The rate at which work is done:

The unit of velocity is :

A combination of two reverse curve used to avoid intervening obstructions like buildings etc :

A quantity having both magnitude and direction is :

The eccentricity of a parabola is usually :

The change in dimension per unit dimension of a body is called :

Hook's law holds upto :

Solder is an alloy of :

An optical instrument used in modern surveying, archaeology, investigation and for military service etc.

A triangle is obtain by joining the pole, zenith and any star on the sphere by arc of great circle is:

The science and art of collecting information about objects, area or phenomena from distance without being in physical contact with them :

The reverse process of surveying in with the data are transferred from drawing to the ground:

"Tatwa Prakasika Ashram' was started by:

The device, that measures the depth of the sea :

"The Darsanamala', famous work of Sree Narayana Guru, was written in - language.

The Practice of 'Sati' was banned by :

Ezhuthachan Award Winner of 2014:

Who was the author of 'Anandakkummi"?

"The Partition of Bengal' was revoked in:

Who directed the film 'Kuttisrank"?

The editor of 'Yuktivadi Magazine':

'Durand Cup' associated with:

One of the Nobel Prize winner of Chemistry in 2014

Who was the author of the work 'Lanka Mardhanam"?

The renaming of Planning commission called "NITI Aayog' was formed on:

"Saptanga Theory' of state was associated with:

The first Kerala State Political Conference was held on 23 April 1921 at Ottappalam under the Presidentship of

The head quarters of UNICEF:

'Blue Revolution' aims for increasing

The Pictures carved at Edakkal caves in Wayanad noticed by time.

The Government of India appointed the 'Hunter Committee to investigate into and report on:

"Melmundu kalapam' was started by —