It is a tool  used to pull wires into raceway or conduit.

A tool used to bend electrical metal tubing.

Which of the following tool should be included in request/borrowers form if the job includes skinning, cutting, and connecting wires or making splices?

These tools are used in making splices and tap connections of wires.

These are tools used to drive and pull out screws.

Some tools or equipment that cannot be repaired.

A written or printed request for something that is needed.

It is a list of tools,materials, property, and other resources.

What is the purpose of turning the drill on before attempting to drill a hole?

The grinding disc should be replaced when worn out and reduced to _________ of its original diameter.

Grinding with the portable disc grinder should not be done in an area which ________________.

When operating the portable disc grinder, the grinding disc should be positioned so that the sparks and grit are thrown __________.

It is a drill specifically designed to remove a cylinder of material, much like a hole saw.

What will likely to happen when an engine leaked and lost all its oil?

This refers to the consistency of a lubricant.

Bearing should be applied with _________ because it stay on surfaces longer.

To prevent seizing when drilling, the operator should ____________.

Hands and arms should be protected by wearing __________ when using portable disc grinder.

Which of the following can be done to avoid hand and finger fatigue when using portable disc grinder for extended period of time?

Which of the following could be the cause when a portable grinder is giving off smoke?

The following are example of safe practices in using power tools except __________.

It is a drilling hazard where chips of the materials being drilled break and fly off while being worked which could cause bodily injury.

It is the part of a cordless drill responsible for the control of bit spin direction.

Which of the following could be the cause when grinder is turning slowly?

A cordless drill uses _____________ as a power source instead of power cord plugged to a receptacle outlet.

Before plugging in any power tool, make sure that the power switch is _________.

Before using any power tool, always read, understand and follow__________________.

Never use power tools if you are ________.

In storing electrical power tools and hydraulic tools, commonly used tools should be placed at the __________________ of the cabinet.

Heavy tools like power grinder should be placed at the ________ of the cabinet when stored.

He was the scientist that experimented with thousands of different filaments to find just the right materials to glow well and be long-lasting and eventually produced a bulb that could glow for over 1500 hours.

Which of the following is not true  about incandescent lamp?

The metal wires that glow brightly when electricity flows through them.

The threaded base of the bulb that secures it to the lamp.

Incandescent lamp used in photography and projection service.

The types of incandescent lamps normally used for interior and exterior general and task lighting.

It is a high intensity discharge lamps in which the major portion of the radiation is produced by the excitation of mercury atoms.

It is a type of switch which controls one or more lamp in two different locations.

Which of the following is represented by the slashes across the line representing the conduit?

It is a glow switch that open sand closes the circuit so as to produce a high voltage or inductive kick across the bulb at the filament during the starting period of a fluorescent lamp.

It is a type of tubing which is resistant to moisture, chemical atmosphere and flame retardant. It requires heat when bend is to be made.

The minimum trade size of rigid non-metallic conduit allowed to be used in electrical installation is _________.

It is the maximum trade size of rigid non metallic conduit allowed to be used in electrical installation.

It is an electrical fitting used to secure the conduit when it enters a box, fitting, or other enclosure. It also protects the wire from abrasion.

It is the process of removing the rough edges or burrs left on the conduit after cutting it to prevent any damage to the wire.

A wiring method which uses cleats, mica tube and porcelain tubes, and knobs.

It is the type of knob used for wires smaller than no. 8 AWG.

It is the type of knob used for wires no. 8 AWG and bigger.

In a knob and tube system, which of the following materials is used to provide protection for the wires whenever they cross each other.

It is the most used conduit nowadays because of its economic value.