
Q3 EXAMINATION TLE - CSS 9
Quiz by Eden Javier
Tag the questions with any skills you have. Your dashboard will track each student's mastery of each skill.
Which tool is used to attach connectors to wires?
Which tool is used to cut strip and cut wires?
Which tool is used to hold small parts?
Which of the following shows the correct usage of plier?
The following show the correct usage of screwdriver EXCEPT for:
This occurs when a hand tool is being used for something other than its intended purpose.
Which of the following is the correct way to use a screwdriver to tighten a screw?
Which of the following is the correct way to use a screwdriver to loosen a screw?
What will happen if you over-tighten the screw?
Which of the following is the purpose of wearing an anti-static wrist strap when working on electronic components?
Which of the following is a safe practice when working with an AC electric power cord?
Which of the following does NOT follow Occupational Health and Safety Standards?
The following are the primary functions of lubrication EXCEPT for:
Sandpaper, water stones, diamonds are examples of:
It places all the requisite things in the best position to perform their duties at the workplace.
Which of the following steps should NOT be taken into consideration to keep tools in good condition during storage?
This refers to the flow of current in two directions.
Which of the following is an example of direct current wherein current flow in one direction?
This states that the current in a circuit is directly proportional to the total voltage acting in the circuit, for a constant current, and inversely proportional to the total resistance of the circuit.
What is the formula in getting the resistance?
What is the formula in getting the voltage?
What is the formula in getting the current?
A circuit has a resistance of 20 ohms and a current of 5 amps flowing through it. What is the voltage across the circuit?
A circuit has a voltage of 120 volts and a resistance of 15 ohms. What is the current flowing through the circuit?
A circuit has a voltage of 24 volts and a current of 3 amps flowing through it. What is the resistance of the circuit?
Which of the following safety device a safety device that is used to protect the electrical circuit from excessive current effects?
This is a wire that is sufficient for holding an electrical current.
This is a mechanism used to break or pass an electrical current to another conductor.
Which of the following is NOT an example of Passive Device?
Which of the following electronic components is used to regulate current and voltage?
Which of the following electronic components can store electrical power?
Which of the following is NOT an example of Active Device?
What does LED stand for?
Eliza is figuring out how to mount the resistor to the circuit board, what is the best equipment that will help her to mount firmly the resistor?
Edward is soldering a stranded wire, which of the following soldering tip must be applied?
This is used extensively for outside wiring to extend the length of wire from one end to another.
Arrange the steps in splicing a rat tail join, use number from 1-3.
_______ Place the two ends of bare wire in crossed position
_______Twist the bare conductors about five to seven times
_______Strip the wire insulator at the ends of the conductor to be joined at about 50mm. and clean the es to be joined.
Which of the following is an example of Knotted Tap?
This types of multi-meter have a numeric display, and may also show a graphical bar representing the measured value.
This refers to the parts which selects the different task in measuring such as reading voltage, resistance and ohms.
What is the color of positive probes?
Shelby is measuring the voltage (V-) of a battery cell of 1.5 Volts using Multi-meter, where will she point the Selection Knob?
Identify the types of wiring diagram.

This is the fastening device that is used to hold or secure objects tightly together to prevent movement or separation through the application of inward pressure.
This is a metal alloy usually made of tin and lead which is melted using a soldering iron.
This is the thorough check-up of the entire electrical system, ensuring that all electrical connections and wiring installed comply with the legal safety standards.
For every 8-10 years check the wires to make sure no damage has occurred in the succeeding years.
Which of the following does NOT describe an electrical inspector?
It is the cause of break through fire.