The widest area of the head is the

Spots that mark where the surface of the head changes are:

The bone that protrudes at the base of the skull is the:

The reference point that signals a change in head shape from flat to round or vice versa is the:

The highest point at the top of the head is the:

The area between the apex and the back of the parietal ridge is the:

Lines parallel to the floor are ____ lines

The area at the back part of the neck is the:

Bang area is also known as:

The most commonly used elevations are ___ and ___.

The straight lines used to remove weight or create graduated layers are:

For control during haircutting, the hair is divided into uniform working areas called:

The angle at which the fingers are held when performing a haircut is the:

The line dividing the hair at the scalp, separating one section of hair from another is called a:

A blunt or one-length haircut is a _____ degree haircut:

Line between horizontal and vertical are:

Hair that moves as the haircut progresses is referred to as a:

A section of hair that determined the length the hair will be cut is called:

A guideline that does not move throughout a haircut and all sections are combed to meet that guideline is referred to as a _____ guideline.

Combing the hair away from its natural falling position, to create a length increase in a haircut, example, (long layer) the hair is:

A great haircut always begins with a:

An important point to consider when cutting straight hair it shrinks ______ when it dries

The hair that grows at the outermost perimeter along the face, around the ears, and on the neck is the:

The direction in which the hair grows from the scalp is referred to as:

____ are mainly used to cut blunt or straight lines:

Hair texture is classified as:

Shears that are mainly used to remove bulk are called:

A comb that is mainly used for close tapers is a:

When a softer effect is desired on the ends of the hair use:

Trimmers are mainly used to create crisp outlines and trimming the nape.

Disinfecting your shears after each use can rust the metal.

Allowing someone to use your shears has no effect on the shears.

When palming the shears, hold the comb with your ____ fingers:

After you have combed a subsection into position to free up your cutting hand you need to:

When cutting hair, it is important to always use _______ tension.

When cutting the hair, a rule of thumb is to not cut:

A one-length haircut is also known as a:

Parting the haircut in the opposite way that you cut it to check or precision of line and shape is known as

Curly hair shrinks more than straight hair, anywhere from:

Hair can be cut with a razor on dry or wet hair?

To create very short tapers quickly and go from short length to longer lengths use the:

A technique performed on the ends of the hair using the tips of the shears is known as:

Another version of point cutting is called:

When thinning the hair avoid thinning the:

Always work _____ the growth patterns of the hair when using clippers to ensure that you are cutting evenly.

As a cosmetologist it is legal to trim male clients eyebrow and ear hairs?

Thinning the hair can also be done using the razor.

Cutting the hair with the razor the guard always faces away from you.

The razor cannot be used to remove excess bulk from the hair because it leaves the hair frizzy.

What must be done to the clippers after each service:

Clippers cannot be used without a guard.

When cutting with the clippers, it is recommended to:

How often should the blade in a razor be replaced:

Any haircut you create with shears can also be done with a razor.

Texturizing techniques can be done with:

A section of hair that determines the length the hair will be cut is known as the:

When using the cutting shears the part that the pinky finger rest is called the:

What type of cape do you use when performing a haircut

When using the thinning shears, always cut at least ____ inches from the scalp to avoid short hairs to poke through the haircut

180 degree can also be used for long layered haircuts.