Question 1

What should you do before operating any power tool in the shop?

Accepted Answer

Put on safety goggles and tie back long hair

Answer

Read a book for entertainment

Answer

Listen to music loudly with headphones

Answer

Check your social media notifications

Question 2

When using a tablesaw, you should always:

Accepted Answer

Use a push stick to move stock through the blade

Answer

Keep your fingers close to the blade when cutting

Answer

Remove the blade guard for better visibility

Answer

Keep distractions around the saw

Question 3

Which of the following is a proper shop safety technique when using a bandsaw?

Accepted Answer

Wait for the blade to stop moving to make adjustments

Answer

Wear gloves to protect your hands

Answer

Stand directly in front of the blade while cutting

Answer

Push the stock through the blade with your fingers

Question 4

What should you do before making adjustments to a drill press?

Accepted Answer

Turn off the power and wait for the drill bit to stop spinning

Answer

Adjust the drill press with one hand while holding a tool in the other

Answer

Yell out to get someone's attention to assist you

Answer

Quickly adjust the drill press while it's still on

Question 5

Which of the following is crucial when working with power tools?

Accepted Answer

Follow all instructions and guidelines

Answer

Take frequent breaks to chat with friends

Answer

Use tools for purposes they were not intended for

Answer

Keep your eyes closed to prevent dust from getting into them

Question 6

How should you handle sharp tools or blades in the shop?

Accepted Answer

Cut away from your body, but not directly towards another classmate.

Answer

Keep them loose on your workbench

Answer

Leave them on the floor for easy access

Answer

Juggle them for fun

Question 7

Why should you always unplug power tools after use?

Accepted Answer

Prevent unintended use and accidents

Answer

To save electricity

Answer

In case there's a power outage

Answer

Leave it plugged in for convenience

Question 8

How should you position your hands when using a miter saw?

Accepted Answer

Keep them far away from the blade

Answer

Place them close to the blade for better control

Answer

Wearing gloves to protect from any accidental cuts

Answer

Cross your fingers for good luck

Question 9

How should you approach unfamiliar power tools in the shop?

Accepted Answer

Ask your teacher for guidance

Answer

Experiment with them without reading instructions

Answer

Post about it on social media for advice

Answer

Take them apart to see how they work

Question 10

Which action promotes shop safety when using a drill press?

Accepted Answer

Secure the stock properly and wear eye protection

Answer

Speed up the drill press for faster results

Answer

Keep the chuck key in the chuck while operating

Answer

Use excessive force to push the drill bit through stock

Question 11

What is the purpose of the miter gauge on a tablesaw?

Accepted Answer

To support the board during a crosscut.

Answer

To turn the tablesaw on and off

Answer

To adjust the blade height

Answer

To adjust the saw fence

Question 12

What is the primary purpose of a jointer in woodworking?

Accepted Answer

flattening a face and an edge of a board.

Answer

Hammering nails into wood

Answer

Drilling holes in wood

Answer

Sanding wood surfaces

Question 13

When using a jointer, what is the correct direction to push the wood across the cutter head?

Accepted Answer

With the grain

Answer

Perpendicular to the grain

Answer

Diagonal to the grain

Question 14

What safety gear should be worn when operating a jointer?

Accepted Answer

Safety goggles

Answer

Apron and earmuffs

Answer

Sandals and shorts

Answer

Necklace and wristwatch

Question 15

Which of the following wood defects can a jointer help to address?

Accepted Answer

Warping

Answer

Knots

Answer

Cuts

Answer

Cracks

Question 16

What is the purpose of the guard on a jointer?

Accepted Answer

To protect the user from the cutter head

Answer

To adjust the depth of cut

Answer

To hold the wood in place

Answer

To provide a flat surface for the wood

Question 17

What is the purpose of the riving knife on a tablesaw?

Accepted Answer

To prevent the kerf from closing up behind the blade

Answer

To prevent the wood from twisting during cutting

Answer

To help guide the workpiece through the cut

Answer

To adjust the blade angle

Question 18

Which part of the tablesaw is used to make rip cuts by adjusting its distance from the blade?

Accepted Answer

Fence

Answer

Miter gauge

Answer

Dust collection port

Answer

Push stick

Question 19

Which part of the tablesaw is responsible for raising and lowering the blade?

Accepted Answer

depth of cut hand wheel

Answer

Riving knife

Answer

Throat plate

Answer

Blade guard

Question 20

Which part of the tablesaw helps to prevent the material from pinching against the blade?

Accepted Answer

riving knife

Answer

Throat plate

Answer

Miter gauge

Answer

Blade guard

Question 21

Where is the best place to stand when using a table saw?

Accepted Answer

To the Side of the Blade

Answer

Behind the Blade

Answer

In Front of the Blade

Answer

It doesn't Matter.

Question 22

How far off the surface of the material you are cutting should the table saw blade be set?

Accepted Answer

1/4" inches

Answer

1 inches

Answer

3/8 inches

Answer

2 inches

Question 23

What will almost always cause kickback on the table saw?

Accepted Answer

using a fence when cross cutting wood.

Answer

feeding the wood too fast.

Answer

Ripping thin strips of wood

Answer

removing the plastic blade guard

Question 24

When do we use a fence on the tablesaw?

Accepted Answer

When Rip Cutting.

Answer

At all times

Answer

When cutting angles

Answer

When cross cutting

Question 25

Kickback is.....

Accepted Answer

A dangerous situation in which a workpiece is forcibly ejected from a machine, often at tremendous speed

Answer

A device (usually on a drill or drill press) used to clamp a bit in place, capable of gripping a large range of bit or shank sizes and often utilizing a key to operate

Question 26

Use a push stick when.

Accepted Answer

your hands are close to the blade

Answer

only when you are affraid

Answer

always use a push stick no matter what

Answer

Only when you have removed the plastic guard from the table saw.

Question 27

The best type of shoes to wear in the shop are...

Accepted Answer

Closed toed shoes

Answer

High Heeled shoes

Answer

Cleats

Answer

Sandals or slides.

Question 28

Planner is used to...

Accepted Answer

Flatten / smooth one face of a board / bring it down to a specific thickness

Answer

Cut boards to width

Answer

Cut boards to length

Question 29

Long hair must be what while in the shop....

Accepted Answer

Tied Back

Answer

Straightened

Answer

Shaved off

Answer

Curled

Question 30

Long flowing scarfs are allowed in the shop

Accepted Answer

false

Answer

true

Question 31

You must never _______________ in the shop.

Accepted Answer

Horse around / rough house

Answer

Work

Answer

Walk

Answer

Listen to music

Question 32

If you get cut, what should you do?

Accepted Answer

Tell Mr Rouse

Answer

hide the injury

Question 33

If you are cut, what should you do to stop the bleeding?

Accepted Answer

Apply direct pressure to the wound

Answer

Flush the wound with water

Answer

All of the above

Answer

Wander around the school, looking for help

Question 34

When you are in the shop, you are able to use ...

Accepted Answer

Only the tools you been taught to use.

Answer

Any tool, any time.

Answer

Only the tools you bring

Question 35

Safety glasses / side shields must be worn in the shop...

Accepted Answer

at all times

Answer

when using tools

Answer

when sanding

Question 36

What is the main use of a bandsaw?

Accepted Answer

To cut curves or irregular shapes

Answer

Cross Cut Stock

Answer

Rip Cut stock

Answer

To cut thick stock

Question 37

What should you do if a drill bit gets stuck

Accepted Answer

Turn off the machine

Answer

Grab the bit with your hands

Answer

Release the board so it can spin.

Answer

Pull harder on the handle

Question 38

When is it ok to use the jointer without the gaurd?

Accepted Answer

Never

Answer

Stock is too wide

Answer

When making special cuts

Answer

When the guard is broken

Question 39

When using the table saw to rip cut wood, which accessory supports the wood through the cut?

Accepted Answer

Hold the wood against the fence

Answer

Neither

Answer

Hold the wood against the miter slider

Question 40

What accessory should be used when crosscutting on the table saw?

Accepted Answer

Miter slider

Answer

Table slot

Answer

Fence

Answer

Push stick

Question 41

It's not a good idea to wear _____________ when using the machines

Accepted Answer

gloves

Answer

ear plugs

Answer

safety glasses

Question 42

What should you do after you have completed your cut on the table saw.

Accepted Answer

wait for the blade to stop moving

Answer

lock the blade

Answer

clear the scrap pieces away

Answer

un plug the saw

Question 43

What is the measurement shown in the photo below.

Accepted Answer

3 7/8"

Answer

3 1/8"

Answer

4 7/8"

Answer

3 1/2"

Question 44

Which part turns the saw on?

Accepted Answer

Part "A"

Answer

Part "C"

Answer

Part "F"

Answer

Part "B"

Question 45

When your fingers must pass into area "C" what accessory must you use?

Accepted Answer

Push Stick

Answer

Fence

Answer

Miter Slider

Answer

Crosscut sled

Question 46

Is this table saw set up to make a cross cut or a rip cut?

Accepted Answer

Rip Cut

Answer

Crosscut

Question 47

What is the name of this tool?

Accepted Answer

Jointer

Answer

Planer

Answer

Bandsaw

Answer

Table Saw

Question 48

Can you edge joint a board that is shorter than Part "C?"

Accepted Answer

NO

Answer

YES

Question 49

Identify the Gaurd.

Accepted Answer

Part "A"

Answer

Part "B"

Answer

Part "F"

Answer

Part "C"

Question 50

What is the purpose of this tool?

Accepted Answer

Flattening

Answer

Cross Cutting

Answer

Cutting curves

Answer

Rip Cutting

Question 51

Which Part will adjust the depth of cut?

Accepted Answer

Part "A"

Answer

Part "C"

Answer

Part "D"

Answer

Part "B"

Question 52

What is the purpose of this tool?

Accepted Answer

Cutting Irregular Shapes

Answer

Flattening

Answer

Rip Cutting

Answer

Cross Cutting

Question 53

Where should your hands never go?

Accepted Answer

Part A

Answer

Part D

Answer

Part B

Answer

Part C

Related quizzes

Related quizzes