To prevent any movement when drilling and assembling, what is used to hold pieces of material together?

If you are uncertain about the safe operation of any piece of equipment, you should:

Which of the following is not a way to guard against injury when working with compressed air?

What must all employees use to protect their eyes and face from flying objects, molten metal, liquid chemicals, acids, and chemical gases or vapors?

What will be required for you to wear if there is a danger of foot injuries due to falling or rolling objects, objects piercing the sole, and where you may be exposed to electrical hazards?

A quality hole meets which of the following requirements?

Why is drilling a quality hole important?

What is the most common type of drill bit?

What type of drill bit is capable of drilling two different diameter holes in one drilling operation?

On a drill motor, what does RPM stand for?

What tool prevents you from drilling too deep and prevents you from damaging a part that may be behind the material you are drilling?

What is one of the most common reasons to chamfer a hole?

What is the most common countersink angle in the aerospace industry?

What is designed to keep the countersink tool accurately centered in the drilled hole?

What specialized tool enables accurate control of the depth of the countersink?

What do you refer to for the correct fastener application?

What part of a threaded bolt applies pressure to one side of the materials that are being fastened?

What is the unthreaded portion of the bolt?

What part of a drill bit is grasped by the chuck of a drill?

A high torque wrench with two closed ends.

A screwdriver with screw heads offset 90 degrees from each used to remove or replace screws in tight areas.

Typically, what color are right cutting aviation snips?

Which type of nail gun is commonly used for small, delicate projects?

What is a key advantage of using nail guns?

What is the function of a rivet in a joint?

What power tool is mainly used for cutting irregular, curved shapes, large parts, and thick material but can also be used to create straight cuts?

What are the cutouts between saw blade teeth that allow material to be ejected when cutting?

What should you use to hold the workpiece, when cutting a small workpiece or performing a narrow cut on a table saw?

On a circular saw, knobs/levers located in front of the motor for adjusting the angle of the plate relative to the saw blade.

Cutters used as side cutters to cut wire.

When sanding a workpiece on a disc sander, you should always move the workpiece against which portion of the rotating disc?

______ gear has more torque, less speed

Battery type that is subject to memory effect.

Battery types that are expensive and sensitive to high temperatures.

This type of joining process consists of screws and bolts.

This type of joining process has a disadvantage of not resisting peeling.

This type of wood joint is a traditional type where two pieces of wood sit side by side with the butt of one work piece adjacent to the butt of another piece.

TIG welding is a type of welding. What does TIG stand for?

Which type of welder is typically faster and easier to use?

What type of weld is used to join two surfaces typically at 90 degrees?

A bolt with a circular ring on the head end. Used for attaching a rope or chain.

Bolts with a hexagonal head with threads for use with a nut or tapped hole.

A screwdriver with a flat tip.

True or False: Unlike a tool, a piece of equipment performs more than one operation at a time.

Which government agency is responsible for regulating safety for general industry and construction workers?

True or False? When an employee voluntarily purchases and wears his or her own PPE and is allowed to use it at the workplace, the company is not required to reimburse the employee for that equipment.

True or False? This is a free country, and the company can't make you wear PPE—it can only recommend it.

True or False? OSHA doesn't have specific PPE regulations, but it can use the "General Duty" clause for PPE-related violations.

True or False? If you want to find out about specific hazards associated with a particular substance, check the Material Data Safety Sheet.

True or False? Typically, the company will not pay for nonspecialty prescription safety eyewear, everyday clothing, and ordinary clothing and skin creams used solely for protection from the weather.

Should you use a dull chisel?

The countersink ________ is the part of the countersink tool that is held in the drill chuck.

What is a nail gun?

What part of the band saw assists in making angled cuts and helps stabilize the workpiece?

What does the orbital action dial do on a jigsaw?

Battery types that take 1-2 hours to charge.

Battery types that are expensive and sensitive to high temperatures.

This is a charger type that can charge batteries faster but shortened the battery's lifespan.

A charger type that can adjust the charging rate based on how much charge the battery needs, extending the battery life.

Battery types that are better for the environment than nickel-cadmium batteries.

Battery type that is the most common rechargeable battery used in portable electronics and electric vehicles.

______ gear has more speed, less torque

Battery types that take 3-6 hours to charge.

Which component of the battery powered drill regulates the turning force and the amount of torque?

Battery types that have a good low-temperature performance and has an ultra-fast charge with little stress.

Which component of the battery powered drill allows for alternating between gears and speed ranges?

On a circular saw, knobs/levers located in front of the motor for adjusting the angle of the plate relative to the saw blade.

Battery type that is durable and has a high current output.

What drill press component is set into the base and supports the table, the spindle, the chuck, the drill head, and the motor?

When drilling into a workpiece with a drill press, you want to start with ________.

What power tool is mainly used for cutting irregular, curved shapes, large parts, and thick material but can also be used to create straight cuts?

True or False: In general, the smaller the drill bit, the greater the RPM required.

What part of the drill press is usually comprised of a set of three handles radiating from a central hub?

What component of the drill press is used to create a stable support surface for the workpiece?

What component of the drill press is designed to shield the operator from the moving parts of the drill press?

What component of the drill press is a lever attached to one side of the motor that changes the gear ratios to change the spindle speed?

What tooth type on the band saw blades have zero rake and shallow gullets?

What is the first step in setting up a pedestal grinder correctly?

What is the most important reason for checking the grinding wheel, on a pedestal grinder, for cracks and damages before using it?

The emergency stop button on a pedestal grinder can only be used in cases of actual emergencies.

What is the importance of safety measures when working with a pedestal grinder?

Which blades are the hardest, most durable, and most expensive blades for power saws?

More teeth per inch will make a blade cut ________.

Which saw blade material is best suited to high speed wood cutting?

What are the cutouts between saw blade teeth that allow material to be ejected when cutting?

What should you use to hold the workpiece, when cutting a small workpiece or performing a narrow cut on a table saw?

When sanding a workpiece on a disc sander, you should always move the workpiece against which portion of the rotating disc?

When adjusting the angle of the table of the disc/belt sander, what gap should you have between the table edge and the disc or belt?

True or False: Sandpaper with a high grit count is coarser than sandpaper with a low grit count.

What is the disc material (for disc sanders) that is perhaps most common, comes in a wide variety of grits, and can be used on metal?

How far away from the grinding wheel on a pedestal grinder should the spark deflector be?

Which type of grinder wheel, on a pedestal grinder, should you use on non-ferrous metals?

On a pedestal grinder, dip the material in water when it gets hot.

With sandpaper, the lower the grit, ________.

What is the width of the saw cut that is the measure of the material removed by the saw blade?

Which type of nail gun is most commonly used in construction?

What is the main purpose of a framing nail gun?

What type of nails are typically used in a framing nail gun?

What is a brad nail gun used for?

What is the recommended safety gear to wear when using a framing nail gun?

What is a siding nail gun?

What is a roofing nail gun?

What is a common type of nail used with a roofing nail gun?

Which type of nail gun is commonly used for small, delicate projects?

What is a key advantage of using nail guns?

Which type of rivet gun is commonly used for heavy-duty applications?

What is the function of a rivet in a joint?

Which type of rivet is commonly used in structural applications?

Which type of rivet is commonly used for joining metal sheets?

Which type of rivet is commonly used for joining leather, fabric, or other soft materials?

Which type of rivet is commonly used for attaching nameplates or small components?

Which of the following is a type of manual rivet gun?

Which safety equipment should be worn when using a rivet gun? Select the BEST answer

What is one of the most common reasons to chamfer a hole?

Countersink tools are identified by the size of the body, the countersink ________, and the size of the pilot.

A microstop tool is a specialized tool that enables accurate control of the ________ of the countersink.

A ________ countersink tool is a specialized tool designed to chamfer, deburr, or countersink the back side of a drilled hole.

True or False: Countersink angles will vary based upon the material you are cutting.

True or False: Only flush head fasteners have a fillet under the head of the fastener. Protruding head fasteners do not have fillets.

Type of deburring and countersink tool, with zero-flutes, helps with removing burrs and finishing edges for countersink holes

Which of the following is not a material that is commonly used for countersink tools?

A deburring tool with a double-edge countersink cutter placed in a wooden handle or chuck.

Most types of bolts and other fasteners have a slight radius at the transition between the shank and head that helps distribute the stress load on the fastener. This radius is commonly called a ________.

According to what we learned in class, you should have what finger on the trigger when using a hand drill?

True or False: A large edge margin hole is a hole that is too close to the edge of the material.

True or False: A quality hole is one that is free of burrs and sharp edges.

Using the correct drill speed and ________ has a significant impact on the quality of a drilled hole and on the life of the drill bit.

Type of hole defect that is the correct size at the surface but bows as it becomes deeper.

Type of hole defect when you begin drilling a crooked hole, then stop, reorient the drill bit so that it is perpendicular and continue drilling straight.

Type of hole defect when the drill bit is not seated properly before you pull the trigger and the drill moves around the material when the trigger is pulled.

Type of hole defect that has a full size hole that touches the pilot hole but the pilot hole still exists.

When a hole is ________, it appears slightly grooved on the interior.

Tools used to tighten or loosen nuts.

Tools used to move nails, staples, etc., into wood.

Tools used to make holes and/or small marks.

Tools used to smooth or change the contour of materials.

Tools used to cut materials in small strokes, typically metals.

You need a pliers that twists safety wire. Please select the best pliers to use for this.

You need to measure the amount of turning/twisting force applied to the nut, bolt, or screw. What type of wrench are you going to use? Select the best answer.

You need to rough cut a long, thick piece of wood. What type of hand saw would you use?

What are two common types of teeth cuts on files?

Typically, what color are left cutting aviation snips?

This filing technique is a little more unusual and involves holding a file at each end and using it in a similar way to sandpaper.

This type of filing is used to smooth and shape cylindrical pieces of material, such as wooden chair legs.

What type of burr is this: Machined material bulges outward from downward force

What type of burr is this: Portions of the material falls away from the main workpiece

Typically, what color are straight cutting aviation snips?

True or False? PPE should always be thrown away after each use.

Which of the following hazards often require PPE?

True or False: The greatest hazards posed by hand tools result from misuse and improper maintenance.

You should always use the ________ tool for the job.

You should keep impact tools free of ________ heads.

Power tools are driven ________.

A tool is a handheld or power device used to perform ________ at a time.

To prepare yourself to work with hand tools, you should ________.

True or False: Cutting tools may be hand tools or power tools.

Which safety precaution keeps you safe when working with hand tools?

Hand tools are powered ________.

A high torque wrench with two closed ends.

Pliers commonly used for turning and holding nuts and bolts, gripping odd shaped objects, and clamping materials.

Wrench that is adjustable to different sized nuts and bolts.

Pliers that can be locked in place.

Used to drive out small objects, cotter keys, and key locks.

A wrench with both open and closed ends.

A screwdriver with screw heads offset 90 degrees from each used to remove or replace screws in tight areas.

A screwdriver that has a head with ridges that intersects like an X.

True or False: Securely holding materials during the drilling and assembly processes is critical to product quality.

True or False: Accident prevention depends upon the use of approved practices, safety devices and common sense.

The emergency stop button on a pedestal grinder can only be used in cases of actual emergencies.

True or False: Always refer to your work instructions for the appropriate personal protective equipment to use.

When countersinking, the head of the fastener should sit flush or slightly above the surface of the surrounding structure.

True or False: The safe and efficient operation of any airplane is greatly dependent upon the correct selection and use of aircraft hardware.

A nut and bolt is an example of a permanent joint.